View A5970AD_4598729.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

A5970AD
Up to 1 A switch step down switching regulator for automotive applications
Features
Qualified following the AEC-Q100 requirements (temperature grade 3), see PPAP for more details. Temperature range -40 C to 85 C 1 A DC output current Operating input voltage from 4.4 V to 36 V 3.3 V / (2 %) reference voltage Output voltage adjustable from 1.235 V to 35 V Low dropout operation: 100 % duty cycle 500 kHz Internally fixed frequency Voltage feedforward Zero load current operation Internal current limiting Inhibit for zero current consumption Synchronization Protection against feedback disconnection Thermal shutdown The A5970AD is a step down monolithic power switching regulator with a switch current limit of 1.35 A so it is able to deliver more than 1 A DC current to the load depending on the application conditions. The output voltage can be set from 1.235 V to 35 V. The device uses an internal P-channel D-MOS transistor (with a typical RDS(on) of 250 m) as switching element to avoid the use of bootstrap capacitor and guarantee high efficiency. An internal oscillator fixes the switching frequency at 500 kHz to minimize the size of external components. Having a minimum input voltage of 4.4 V only, it is particularly suitable for 5 V bus, available in all computer related applications. Pulse by pulse current limit with the internal frequency modulation offers an effective constant current short circuit protection.
L1 15uH

SO-8
Description
Applications
Dedicated to automotive applications
Figure 1.
Application schematic
OUT SYNCH 4 2 Vout=3.3V
VIN=4.4V to 35V
VCC COMP
C4 C1 10uF 35V CERAMIC C3 220pF R3 4k7 22nF
8
1
A5970AD
FB 6 5 7 GND INH 3
D1 STPS340U
R1 5k6 C2 100uF 10V R2 3k3
VREF 3.3V
May 2008
Rev 1
1/16
www.st.com 1
A5970AD
1
Pin settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.1 1.2 Pin connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Pin description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2
Electrical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.1 2.2 Maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Thermal data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
3 4
Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Functional description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
4.1 4.2 4.3 4.4 4.5 4.6 4.7 4.8 Power supply and voltage reference . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Voltages monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Oscillator and synchronizator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Current protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Error amplifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 PWM comparator and power stage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Inhibit function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Thermal shutdown . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
5
Additional features and protections . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
5.1 5.2 5.3 Feedback disconnection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Output overvoltage protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Zero load . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
6
Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
2/16
A5970AD
1
1.1
Pin settings
Pin connection
Figure 1. Pin connection (top view)
1.2
Pin description
Table 1.
N 1
Pin description
Pin OUT Regulator output. Master/slave synchronization. When it is open, a signal synchronous with the turn-off of the internal power is present at the pin. When connected to an external signal at a frequency higher than the internal one, then the device is synchronized by the external signal. Connecting together the SYNC pin of two devices, the one with the higher frequency works as master and the other one, works as slave. A logical signal (active high) disables the device. With IHN higher than 2.2 V the device is OFF and with INH lower than 0.8 V, the device is ON. If INH is not used the pin must be grounded. When it is open, an internal pullup disables the device. E/A output for frequency compensation. Feedback input. Connecting directly to this pin results in an output voltage of 1.235 V. An extenal resistive divider is required for higher output voltages (the typical value for the resistor connected between this pin and ground is 4.7 k). 3.3 V VREF. No cap is requested for stability. Ground. Unregulated DC input voltage. Description
2
SYNCH
3
INH
4
COMP
5
FB
6 7 8
VREF GND
VCC
3/16
A5970AD
2
2.1
Electrical data
Maximum ratings
Table 2.
Symbol V8 V1 I1 V4 , V5 V3 V2 PTOT Tj TSTG Input voltage OUT pin DC voltage OUT pin peak voltage at t = 0.1s Maximum output current Analog pins INH SYNCH Power dissipation at TA 70 C Operating junction temperature range Storage temperature range
Absolute maximum ratings
Parameter Value 40 -1 to 40 -5 to 40 int. limit. 4 -0.3 to VCC -0.3 to 4 0.75 -40 to 150 -55 to 150 V V V W C C Unit V V V
2.2
Thermal data
Table 3.
Symbol RthJA
Thermal data
Parameter Maximum thermal resistance junction-ambient SO8 120 (1) Unit C/W
1. Package mounted on board
4/16
A5970AD
3
Electrical characteristics
Table 4.
Symbol
Electrical characteristics (TJ = -40 C to 125 C, VCC = 12 V, unless otherwise specified)
Parameter Operating input voltage range MOSFET on resistance Maximum limiting current Switching frequency Duty cycle Test condition Min 4.4 0.250 Typ Max 36 0.5 Unit V A 570 100 kHz %
VCC
RDS(on) IL fSW
VCC= 4.4 to 36 V
1.35 430 0
1.8 500
Dynamic characteristics (see test circuit). V5 Voltage feedback Efficiency 4.4 V < VCC < 36 V V0 = 5 V, VCC = 12 V 1.220 1.235 90 1.25 V %
DC characteristics Iqop Iq Iqst-by Inhibit Device ON INH threshold voltage Device OFF Error amplifier VOH VOL Io source High level output voltage Low level output voltage Source output current VFB = 1 V VFB = 1.5 V VCOMP = 1.9 V; VFB = 1 V VCOMP = 1.9 V; VFB = 1 V Ib Source bias current DC open loop gain gm Transconductance RL= 50 2.5 57 2.3 4 A dB mS 1 1.5 190 300 3.5 0.4 V V A 2.2 V 0.8 V Total operating quiescent current Quiescent current Total stand-by quiescent current Duty cycle = 0; VFB=1.5 V Vinh > 2.2 V 50 5 7 2.7 100 mA mA A
Io sink
Sink output current
mA
ICOMP = -0.1 mA to 0.1 mA; VCOMP = 1.9 V
8
5/16
A5970AD Table 4.
Symbol Synch function High input voltage Low input voltage Slave synch current Master output amplitude Output pulse width Reference section Reference voltage IREF = 0 to 5 mA 3.234 3.2 3.3 3.3 3.366 3.399 V V
Electrical characteristics (continued) (TJ = -40 C to 125 C, VCC = 12 V, unless otherwise specified)
Parameter Test condition Min Typ Max Unit
VCC = 4.4 to 36 V; VCC = 4.4 to 36 V;
Vsynch = 0.74 V(1) Vsynch = 2.33 V Isource= 3 mA No load, Vsynch= 1.65 V
2.5
VREF 0.74
V V mA
0.11 0.21 2.75 0.20 3 0.35
0.25 0.45
V s
VCC = 4.4 V to 36 V
Line regulation Load regulation Short circuit current
1. Guaranteed by design.
IREF = 0 mA
VCC = 4.4 V to 36 V
IREF = 0 mA 5
5 8 18
10 15 30
mV mV mA
6/16
A5970AD
4
Functional description
The main internal blocks are shown in Figure 2, where is reported the device block diagram. They are:

A voltage regulator that supplies the internal circuitry. From this regulator, a 3.3 V reference voltage is externally available. A voltage monitor circuit that checks the input and internal voltages. A fully integrated sawtooth oscillator whose frequency is 500 kHz Two embedded current limitations circuitries which control the current that flows through the power switch. The pulse by pulse current limit forces the power switch OFF cycle by cycle if the current reaches an internal threshold, while the Frequency Shifter reduces the switching frequency in order to strongly reduce the duty cycle. A transconductance error amplifier. A pulse width modulator (PWM) comparator and the relative logic circuitry necessary to drive the internal power. An high side driver for the internal P-MOS switch. An inhibit block for stand-by operation A circuit to realize the thermal protection function. Block diagram

Figure 2.
7/16
A5970AD
4.1
Power supply and voltage reference
The internal regulator circuit (shown in Figure 2) consists of a start-up circuit, an internal voltage preregulator, the bandgap voltage reference and the bias block that provides current to all the blocks. The starter gives the start-up currents to the whole device when the input voltage goes high and the device is enabled (inhibit pin connected to ground). The preregulator block supplies the bandgap cell with a preregulated voltage VREG that has a very low supply voltage noise sensitivity.
4.2
Voltages monitor
An internal block senses continuously the VCC, VREF and VBG. If the voltages go higher than their thresholds, the regulator starts to work. There is also an hysteresis on the VCC (UVLO). Figure 3. Internal regulator circuit
4.3
Oscillator and synchronizator
Figure 4 shows the block diagram of the oscillator circuit. The clock generator provides the switching frequency of the device that is internally fixed at 500 kHz. The frequency shifter block acts reducing the switching frequency in case of strong overcurrent or short circuit. The clock signal is then used in the internal logic circuitry and is the input of the ramp generator and Synchronizator blocks. The ramp generator circuit provides the sawtooth signal, used to realize the PWM control and the internal voltage feed forward, while the synchronizator circuit generates the synchronization signal. Infact the device has a synchronization pin that can works both as master and slave. As master to synchronize external devices to the internal switching frequency.
8/16
A5970AD As slave to synchronize itself by external signal. In particular, connecting together two devices, the one with the lower switching frequency works as slave and the other one works as master. To synchronize the device, the SYNC pin has to pass from a low level to a level higher than the synchronization threshold with a duty cycle that can vary approximately from 10 % to 90 %, depending also on the signal frequency and amplitude. The frequency of the synchronization signal must be at least higher than the internal switching frequency of the device (500 kHz). Figure 4. Oscillator circuit
4.4
Current protection
The A5970AD has two current limit protections, pulse by pulse and frequency fold back. The schematic of the current limitation circuitry for the pulse by pulse protection is shown in Figure 5. The output power PDMOS transistor is split in two parallel PDMOS. The smallest one has a resistor in series, RSENSE. The current is sensed through Rsense and if reaches the threshold, the mirror is unbalanced and the PDMOS is switched off until the next falling edge of the internal clock pulse. Due to this reduction of the ON time, the output voltage decreases. Since the minimum switch ON time (necessary to avoid false overcurrent signal) is not enough to obtain a sufficiently low duty cycle at 500 kHz, the output current, in strong overcurrent or short circuit conditions, could increase again. For this reason the switching frequency is also reduced, so keeping the inductor current under its maximum threshold. The frequency shifter (see Figure 4) depends on the feedback voltage. As the feedback voltage decreases (due to the reduced duty cycle), the switching frequency decreases too.
9/16
A5970AD Figure 5. Current limitation circuitry
4.5
Error amplifier
The voltage error amplifier is the core of the loop regulation. It is a transconductance operational amplifier whose non inverting input is connected to the internal voltage reference (1.235 V), while the inverting input (FB) is connected to the external divider or directly to the output voltage. The output (COMP) is connected to the external compensation network. The uncompensated error amplifier has the following characteristics: Table 5. Uncompensated error amplifier
2300 S
Tranconductance Low frequency gain Minimum sink/source voltage Output voltage swing Input bias current Note:
65 dB 1500 A/300 A 0.4 V/3.65 V 2.5 A
The error amplifier output is compared with the oscillator sawtooth to perform PWM control.
4.6
PWM comparator and power stage
This block compares the oscillator sawtooth and the error amplifier output signals generating the PWM signal for the driving stage. The power stage is a very critical block cause it has to guarantee a correct turn on and turn OFF of the PDMOS. The turn ON of the power element, or better, the rise time of the current at turn on, is a very critical parameter to compromise. At a first approach, it looks like the faster it is the rise time, the lower are the turn on losses. But there is a limit introduced by the recovery time of the recirculation diode. In fact when the current of the power element equals the inductor current, the diode turns off and the drain of the power is free to go high. But during its recovery time, the diode can be considered as an
10/16
A5970AD high value capacitor and this produces a very high peak current, responsible of many problems:

Spikes on the device supply voltage that cause oscillations (and thus noise) due to the board parasitics. Turn ON overcurrent causing a decrease of the efficiency and system reliability. Big EMI problems. Shorter freewheeling diode life.
The fall time of the current during the turn off is also critical. In fact it produces voltage spikes (due to the parasitics elements of the board) that increase the voltage drop across the PDMOS. In order to minimize all these problems, a new topology of driving circuit has been used and its block diagram is shown in Figure 6. The basic idea is to change the current levels used to turn on and off the power switch, according with the PDMOS status and with the gate clamp status. This circuitry allow to turn off and on quickly the power switch and to manage the above question related to the freewheeling diode recovery time problem. The gate clamp is necessary to avoid that Vgs of the internal switch goes higher than Vgsmax. The ON/OFF control block avoids any cross conduction between the supply line and ground. Figure 6. Driving circuitry
11/16
A5970AD
4.7
Inhibit function
The inhibit feature allows to put in stand-by mode the device. With INH pin higher than 2.2 V the device is disabled and the power consumption is reduced to less than 100 A. With INH pin lower than 0.8 V, the device is enabled. If the INH pin is left floating, an internal pull up ensures that the voltage at the pin reaches the inhibit threshold and the device is disabled. The pin is also VCC compatible.
4.8
Thermal shutdown
The shutdown block generates a signal that turns off the power stage if the temperature of the chip goes higher than a fixed internal threshold (150 C). The sensing element of the chip is very close to the PDMOS area, so ensuring an accurate and fast temperature detection. An hysteresis of approximately 20 C avoids that the devices turns on and off continuously
12/16
A5970AD
5
5.1
Additional features and protections
Feedback disconnection
In case of feedback disconnection, the duty cycle increases versus the maximum allowed value, bringing the output voltage close to the input supply. This condition could destroy the load. To avoid this dangerous condition, the device is turned off if the feedback pin remains floating.
5.2
Output overvoltage protection
The overvoltage protection, OVP, is realized by using an internal comparator, which input is connected to the feedback, that turns off the power stage when the OVP threshold is reached. This threshold is typically 30 % higher than the feedback voltage. When a voltage divider is requested for adjusting the output voltage (see test application circuit), the OVP intervention will be set at: Equation 1
R 1 + R2 V OVP = 1.3 x -------------------- x V FB R2
Where R1 is the resistor connected between the output voltage and the feedback pin, while R2 is between the feedback pin and ground.
5.3
Zero load
Due to the fact that the internal power is a PDMOS, no boostrap capacitor is required and so, the device works properly also with no load at the output. In this condition it works in burst mode, with random repetition rate of the burst.
13/16
A5970AD
6
Package mechanical data
In order to meet environmental requirements, ST offers these devices in ECOPACK(R) packages. These packages have a lead-free second level interconnect . The category of second level interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. ECOPACK is an ST trademark. ECOPACK specifications are available at: www.st.com
14/16
A5970AD
Table 6.
Dim
SO-8 mechanical data
mm Min Typ Max 1.75 0.25 1.65 0.51 0.25 5.00 4.00 1.27 5.80 0.25 0.40 6.20 0.50 1.27 0.228 0.010 0.016 Min 0.053 0.004 0.043 0.013 0.007 0.1890 0.15 0.050 0.244 0.020 0.050 inch Typ Max 0.069 0.010 0.065 0.020 0.010 0.197 0.157
A A1 A2 B C D(1) E e H h L k ccc
1.35 0.10 1.10 0.33 0.19 4.80 3.80
0 (min), 8 (max) 0.10 0.0039
Figure 7.
Package dimensions
15/16
A5970AD
7
Revision history
Table 7.
Date 2-May-2008
7
Document revision history
Revision 1 Initial release. Changes
16/16
A5970AD
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries ("ST") reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST's terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST'S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER'S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
(c) 2008 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com
16/16

▲Up To Search▲

Price & Availability of A5970AD

	To Download A5970AD Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .